Agri-fab LST42B Manual do Utilizador

Model No.LST42BOWNERSMANUALPRINTED IN U.S.A. FORM NO. 49957 (2/06)CAUTION:Read Rules for Safe Operation and Instructions Carefully• Safety• Assembl

10ATTACH CLUTCH IDLER ASSEMBLY TO TRACTORSTEP 12: (SEE FIGURE 12)• Attach the clutch/idler assembly to the tractor frame. Hook the notched suspension

11THIS SECTION IS FOR TRACTORS WITH AN ELECTRIC ATTACHMENT CLUTCH STEP 14: (SEE FIGURE 14)• Attach the two suspension arms to the rear of the clutch/

12STEP 19: (SEE FIGURE 18)• Attach the clutch/idler assembly to the tractor frame. Hook the notched suspension arms onto the two shoulder bolts (M) a

13STEP 22: (SEE FIGURE 21)• Fasten the R.H. Side Plate (bend facing out) to the front three holes shown in the tractor frame using three 3/8" x

14FIGURE 28 RIGHT SIDE VIEWINSTALLING HANGER BRACKETSFor better clearance, lower the tractor's suspension arms using the attachment lift lever.S

15INSTALLING CLUTCH/IDLER ASSEMBLYThis section covers the installation of the Clutch/Idler assembly to tractors with attachment clutches that are eith

16FIGURE 33 RIGHT SIDE VIEWFIGURE 32 RIGHT SIDE VIEWPIVOT LOCK PIN (GG)(use second hole)1/8" HAIRPIN COTTER (EE)ENGAGEMENTRODSTEP 33: (SEE FIG

17FIGURE 36FIGURE 38STEP 36: (SEE FIGURE 36)• Assemble the cable bracket to the clutch/idler assembly using two 5/16" x 3/4" carriage bolts

18FIGURE 40 VIEWED FROM UNDERNEATHFIGURE 39STEP 40: (SEE FIGURE 40)• Assemble the short "V" belt onto the engine pulley and then onto the

19ELECTRIC ATTACHMENT CLUTCHESFIGURE 42TENSIONING CHAIN (JJ)LEFT FRONT HOLEFIGURE 43 VIEW OF BOTTOM STEP 43: (SEE FIGURE 43)• Hook the spring from

2TABLE OF CONTENTSACCESSORIES ...

20FIGURE 46 VIEWED FROM UNDERNEATH1/8" HAIRPINCOTTER (EE)ENGINEPULLEYENGINEPULLEYLeft Sideof TractorKEEPERBOLTIDLERPULLEYSTEP 47: (SEE FIGURE 4

21STEP 48: (SEE FIGURE 47)• Place the lift handle into the lift bracket on the right side of the snow thrower. Fasten the handle to the bracket usin

225/16" NYLOCK NUT (Y)CHUTE CRANKBRACKET5/16" WASHER (Q)CHUTECRANKRODRODSUPPORTBRACKET5/16" x 1"CARRIAGE BOLT (J)SPIRALFIGURE 51

23NOTE:An additional person's help may be required to mount the snow thrower to the front of the tractor.STEP 55: (SEE FIGURE 54)• Place the tr

24INSTALLING THE ATTACHMENT PINSTEP 58: (REFER BACK TO FIGURE 54 ON PAGE 23)• Lift the front of the snow blower to align the holes in the mounting p

25OPERATIONKNOW YOUR SNOW THROWERRead this owner's manual and safety rules before operating your snow thrower.Compare the illustration below with

26RAISING AND LOWERING• To raise, push down on the lift handle until the snow thrower locks in the raised transport position.• To lower, push down s

27SERVICE AND ADJUSTMENTSCAUTION: Before servicing or adjusting the snow thrower, shut off the engine, remove the spark plug wire(s), set the parking

28PARTS TO REMOVE AT END OF SEASON• Remove the clutch/idler assembly. (The two hanger brackets and the two shoulder bolts may be left attached to the

29NOTES

3SAFETYAny power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution a

30PARTSREPAIR PARTS FOR MODEL LST42B 42" SNOW THROWER

31REPAIR PARTS FOR MODEL LST42B 42" SNOW THROWER REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION

32REPAIR PARTS FOR MODEL LST42B 42" SNOW THROWER67366057616558621165585862633233

33 REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION NO. NO. NO. NO. 1 64637 1 Lift Shaft

34REPAIR PARTS FOR MODEL LST42B 42" SNOW THROWER REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION NO. NO. NO. NO.1 43080

35SLOPE GUIDE(Keep this sheet in a safe place for future reference.)Use this guide to determine if a slope is safe for the operation of your tractor a

the fastest way to purchase partswww.speedepart.comREPAIR PARTSAgri-Fab, Inc.809 South HamiltonSullivan, IL. 61951217-728-8388www.agri-fab.com© 2003 A

4EBDGHIKOFXUYCWLQS,TRZKKEENCCBBAANOT SHOWN ACTUAL SIZESHOWN ACTUAL SIZEDDMJJJFFGGIIVPHHALLNNMMHARDWARE PACKAGE CONTENTS

5 REF. QTY. DESCRIPTION REF. QTY. DESCRIPTIONREF. QTY. DESCRIPTION U 2 Bowed Washer V 6 Flanged Nut, 1/4" W 1 Flanged Nut, 5

6CARTON CONTENTS1. Suspension Arms (2)2. Left Hand Side Plate3. Right Hand Side Plate4. Anti-rotation Bracket5. Engagement Rod (Not used on some

7• Remove all parts and hardware packages from the carton. Lay out parts and hardware and identify using the illustrations on pages 4 and 6.NOTE: No

8STEP 4: (SEE FIGURE 4)•Assemble a shoulder bolt (L) and a 3/8" washer (T) to the outside of R.H. side plate, securing it with a 3/8" fl ang

93/8" X 3-1/4"HEX BOLT(A)LARGE SPACER (MM)PULLEY (NN)3/8" LOCKWASHER (O)3/8" HEX LOCK NUT (Z)3/8"WASHER (T)LONG ENDOF HUBSTEP